90° elbow threaded nut M-24X150 to hydraulic pipe Ø 16 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-24X150.- For hydraulic pipe Ø 16 outside.- Heavy series.- Material forged steel.- Bichromated anti-oxidation treatment.
11,50 €
90° elbow threaded nut M-22X150 to hydraulic pipe Ø 15 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-22X150.- For hydraulic pipe Ø 15 outside.- Light series.- Material forged steel.- Bichromated antioxide treatment.
7,83 €
90° elbow threaded nut M-22X150 to hydraulic pipe Ø 14 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-22X150.- For hydraulic pipe Ø 14 outside.- Heavy series.- Material forged steel.- Bichromated anti rust treatment.
10,54 €
90° elbow threaded nut M-20X150 to hydraulic pipe Ø 12 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-20X150.- For hydraulic pipe Ø 12 outside.- Heavy series.- Material forged steel.- Bichromated antioxide treatment.
7,13 €
- Air filter. - Height: 125 mm. - Exterior Diameter 128 mm. - Interior Diameter: 64 mm. - Internal Diameter 2: 64 mm. - Weight: 0.540.
25,12 €
90° elbow threaded nut M-36X200 to hydraulic pipe Ø 25 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-36X200.- For hydraulic pipe Ø 25 outside.- Heavy series.- Material forged steel.- Bichromated anti rust treatment.
27,25 €
90° elbow threaded nut M-30X200 to hydraulic pipe Ø 22 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-30X200.- For hydraulic pipe Ø 22 outside.- Light series.- Material forged steel.- Bichromated anti-oxidation treatment.
15,46 €
90° elbow threaded nut M-30X200 to hydraulic pipe Ø 20 outside DIN 2353
- 90º elbow nut nut to hydraulic pipe DIN 2353.- Thread nut nut M-30X200.- For hydraulic pipe Ø 20 outside.- Heavy series.- Material forged steel.- Bichromated anti rust treatment.
16,75 €
DESCRIPTION
The injector series ZEM are positive displacement injectors (PDIs) that deliver an accurate response and controlled performance of lubrication, in compliance with the exact requirements for a variety of diverse applications. Are predetermined nozzles volumetric that ensure each lubrication point receives the proper amount of
lubricant. Which means that there is nothing to worry about or under lubrication.
OPERATION
The injector series ZEM are PDIs, classic, reliable, and accurate. When the pressure builds up in the manifold, the piston in the injector moves forward, discharging a set amount of lubricant to the lubrication point. While it relieves the pressure, a compression spring re-place the piston in its original position. This movement recharges the injector (camera download) and the injector is ready for the next phase cycle. It is important to note that the lubrication pump used with the injector series ZEM should increase the pressure to a minimum 15 bars (220 psi) to activate the discharge of the injector. The operation recommended pressure is 21 bars (300 psi). Also requires a pressure relief valve to quickly reduce the pressure in the pipe between 0.3 and 0.7 bar (5 to 11 psi) cycles between lubrication. This allows the injector to fully re-charge.
TECHNICAL DATA
Handles oils and fats soft.
Ten volumes of output are available for a wide range of applications and points.
The modular design of the injectors is mounted in the binding for easy installation on the machine.
Possibility of incorporating different injectors in series on the same system.
Each series is available with fittings push to connect or compression fittings standard.
Pressure: Maximum operating: 45 bar (650 psi).
Operation minimum: 15 bars (220 psi).
Alleviating 0.7 bar (11 psi).
Seals: Viton.
Volume of supply: 0.40 cc.